Sie sind vermutlich noch nicht im Forum angemeldet - Klicken Sie hier um sich kostenlos anzumelden Impressum 
W650.deW650 ForumW-Tour/Treff-Kalender
Sie können sich hier anmelden
Dieses Thema hat 9 Antworten
und wurde 511 mal aufgerufen
 W650
kawashima Offline




Beiträge: 78

19.09.2005 17:14
handle bar change(from UPtype to LOW type) Antworten

I decided to change my handle bar from UP type to LOW type.
(I've already ordered handle bar and I'm waiting for it)
Is it better to change brake/clutch wires to LOW type?
My new handle bar is a little bit higher than original low type.(POSH touring bar)
My shop couldn't answer it.

JeanRoule Offline



Beiträge: 596

19.09.2005 22:23
#2 RE: handle bar change(from UPtype to LOW type) Antworten

Hello Kawashima,

It is better because it will look nicer, but it is not necessary.

I run my bike with clip-ons and the original cables. I re-routed the cables in order to hide them as much as possible and that works ok.

Regards
Joris

kawashima Offline




Beiträge: 78

19.09.2005 23:52
#3 RE: handle bar change(from UPtype to LOW type) Antworten

Thank you for your kind response Joris.
I'll check the looks at shop next week and decide whether I order shorter wire or not.

Your W has Clip-ons! It should be very racy W.

der Underfrange Offline



Beiträge: 12.487

20.09.2005 07:41
#4 RE: handle bar change(from UPtype to LOW type) Antworten

Hello Kawashima,

I changed from the UPtype to an M-Bar.
The wire-length was perfect, because I layed them to the other side of the headlight.

In your case, just take care of the curve of the wire.
If it's not to small, you can keep the old wires.

Otherwise, if they don't work smooth and easily, you have to change them.

Greets,

Willi


kawashima Offline




Beiträge: 78

20.09.2005 16:23
#5 RE: handle bar change(from UPtype to LOW type) Antworten

Oh it's a good idea I'll ask shop to try it
Thank you! "M-bar" is nice name to call my new handle bar.

kawashima Offline




Beiträge: 78

05.10.2005 16:08
#6 RE: handle bar change(from UPtype to LOW type) Antworten

My mistake caused this...

BlueThumb Offline



Beiträge: 20

08.11.2005 13:02
#7 RE: handle bar change(from UPtype to LOW type) Antworten

Hi Kawashima,

I made a similar change some time ago, and the brake hose looked about the same as yours. That's why I decided to replace it by a "Steelflex" hose. (sorry, havn't got a picture yet). It does not only improve the looks, but the feeling is much better: Allway a precise and hard triggerpoint and no longer any rubbery feeling.

best regards
bluethumb

KOKOSCHINSKY Offline



Beiträge: 1.055

08.11.2005 14:49
#8 RE: handle bar change(from UPtype to LOW type) Antworten

do those Steelflex have a genuine latex lining?
i am not very well informed on that matter.

BlueThumb Offline



Beiträge: 20

14.11.2005 18:52
#9 RE: handle bar change(from UPtype to LOW type) Antworten

HI,
In fact it's a high quality hydraulic hose. Innermost is a thin rubber hose to keep the thing tight. Around is texture of woven steel wires, finally covered with a transparent plastic layer to prevent scratching. The ends (nipples) are made of aluminium.

I will post some pictures. Please be patient, I have it somewhat hectic at the moment. For the same reason this answer is so belated. Sorry.

Best regards
Bluthumb.

BlueThumb Offline



Beiträge: 20

24.11.2005 10:27
#10 RE: handle bar change(from UPtype to LOW type) Antworten
Hi, here are the pic's
Bottom is conventional :

Top is Direct

Regards
Bluethumb

 Sprung  
Der-Amazon-LinkW650 ForumAsbest
Xobor Einfach ein eigenes Forum erstellen
Datenschutz